| Symptom / Error | FRU / Action in Sequence |
|---|---|
| 10X 101: Interrupt failure. 102: Timer failure. 103: Timer interrupt failure. 104: Protected mode failure. 105: Last 8042 command not accepted. 107: NMI test failure. 108: Timer bus test failure. 109: Low meg-chip select test. |
System board |
| 110 (Planar parity) |
1. Go to "Memory Checkout" on page 12 of the HMM 2. DIMM 3. Detach the expansion unit if it is attached to the computer 4. System board |
| 111 (I/O parity) |
1. Go to "Memory Checkout" on page 12 of the HMM 2. Port replicator 3. System board |
| 127 (Cache error) |
1. CPU card 2. System board |
| 158 (Hard disk password is not set even though the supervisor password is set.) |
Set the password for hard disk drive |
| 159 (Hard disk password is not set the same as the supervisor password.) |
Set the correct password for hard disk drive |
| 161 (Dead battery) |
1. Go to "Backup Battery Checkout (Non-rechargeable)" on
page 15 of the HMM 2. Backup battery 3. System board |
| 163 (Time and date were not set) |
1. Set time and date 2. System board |
| 173 (Configuration data was lost) |
1. Select OK in the error screen; then set the time and
date 2. Backup battery 3. System board |
| 174 (Configuration error: Perform "Checking the Installed Devices List" on page 35 before changing any FRUs) |
1. Check device configuration 2. Hard disk drive 3. System board |
| 175, 177, 178 175: EEPROM CRC #1 error 177: Supervisor password check sum error 178: EEPROM is not functional |
System board |
| 183 (Incorrect password entered at the supervisor password prompt) |
Have the user examine the password. |
| 184 (Power-on password check sum error) |
Reset the power-on password in Easy-Setup. |
| 185 (The start-up sequence is not valid. Probably the computer was powered off when the startup sequence was being updated) |
Reset the startup sequence in Easy-Setup. |
| 186 | System Board |
| 190 (A depleted battery pack was installed when the power was on) |
Go to "Battery Checkout" on page 14 of the HMM |
| 191XX (PM initialization error) |
System board |
| 192 (Fan error) |
1. Fan 2. System board |
| 195 (The configuration read from the hibernation data storage area does not match the actual configuration) |
Check if the configuration was changed. For example, check if the DIMM is added |
| 196 (A read error occurred in the hibernation area of the hard disk drive.) |
1. Run the hard disk drive test 2. Hard disk drive |
| 199XX (Resume error) |
System board |
| 1XX | System board |
| 225 (Unsupported memory module) |
1. Check if a supported DIMM is installed 2. DIMM Card 3. System board |
| 2XX 201: Memory data error. 202: Memory line error 00-15. 203: Memory line error 16-23. 205: Memory test failure on on-board memory. 221: ROM to RAM remap error. |
1. Go to "Memory Checkout" on page 12 of the HMM 2. DIMM 3. System board |
| 301, 303, 304, 305, 3XX (301: Keyboard error.) |
1. Go to "Keyboard or Auxiliary Input Device Checkout" on
page 11 of the HMM 2. Keyboard 3. External numeric keypad 4. External keyboard 5. Keyboard/mouse cable 6. DC/DC card 7. System board |
| 601, 6XX (601: Diskette drive or controller error) |
1. Go to "Diskette Drive Checkout" on page 10 of the
HMM 2. CD-ROM and FDD assembly 3. Diskette 4. System board |
| 602 (Diskette read error) |
1. Go to "Diskette Drive Checkout" on page 10 of the
HMM 2. Diskette 3. CD-ROM and FDD assembly |
| 604 (An unacceptable ID was read from the diskette drive) |
1. Go to "Diskette Drive Checkout" on page 10 of the
HMM 2. CD-ROM and FDD assembly 3. System board |
| 11XX 1101: Serial_A test failure. |
1. Serial device 2. Communication cable 3. System board |
| 12XX 1201: Serial_B test failure. |
1. System board (infrared) |
| 17XX 1701: Hard disk controller failure. 1780, 1790: Hard disk 0 error. 1781, 1791: Hard disk 1 error. |
1. Hard disk drive 2. System board |
| 1801 (Unsupported Port Replicator) |
An unsupported Port Replicator is attached to the computer. |
| 24XX (2401: System board video error) |
System board |
| 808X 8081: PCMCIA presence test failure. (PCMCIA revision number also checked.) 8082: PCMCIA registration test failure. |
1. PC Card slot assembly 2. PCMCIA device 3. System board |
| 860X (Pointing device error when the TrackPoint is disabled) 8601: System bus error - 8042 mouse interface. 8602: External mouse error. 8603: System bus error or mouse error. |
1. External mouse 2. External keyboard 3. System board |
| 861X (Pointing device error when the TrackPoint is enabled) 8611: System bus error - I/F between 8042 and IPDC. 8612: TrackPoint error 8613: System board or TrackPoint error |
1. Reseat the keyboard cable on the DC/DC card 2. Keyboard 3. External mouse 4. DC/DC card 5. System board |
| I9990301 I9990302 I9990305 I9990301: Hard disk error I9990302: Invalid hard disk boot record I9990305: No bootable device |
1. Check that the operating system is installed in the hard
disk drive. If not, install the operating system 2. Reseat the boot device 3. Check the startup sequence for the correct boot device 4. Check that the operating system boots correctly |
| I9990303 (Bank - 2 flash ROM check sum error) |
System board |
| Other codes not listed above. | Go to "Undetermined Problems" on page 32 of the HMM |